V400m
The paper tray outputs printed receipts or vouchers.
Integrated thermal printer
30 lines per second
The contact reader enables communication between the card and the card reader.
Contact reader ISO 14443 A/B
MiFare
ISO 18092 compatible
The magnetic stripe reader reads the data stored on the magnetic stripe of the card for payment processing.
Magnetic stripe reader 3-track
The display shows instructions and transaction information in clear and colorful form.
3.5" TFT color touch display
320 x 480 pixels (HVGA)
The chip card reader reads the card data to enable secure payments.
Chip card reader ISO 7816-3
1.8 V/3.0V/5.0V
Technical data
OS/Processor: 600 MHz, Cortex A9 32-bit RISC processor, 1500 MIPS
Memory: 1024 MB/512 MB Flash/512 MB SDRAM
Dimensions (L x W x H): 16.1 x 7.3 x 5.9 cm
Weight: 412 g
Communication: LTE (4G)/2G, Wifi 2.4 GHz and 5 GHz USB
- Scope of delivery
ATTENTION!
The power supply unit supplied is specially designed for the V400m terminal. Do not use any other power supply unit!
- Commissioning in 5 steps
1. Wiring diagram
First connect the cable to the charging cradle or alternatively directly to the terminal. Then connect the power supply unit to the power supply.
2. Setting up the battery
The terminal battery can be charged either directly or via the charging cradle.
3. Inserting or changing the paper roll
Pull the small locking plate upwards, the cover pops open.
Tilt the cover backwards.
Remove the center sleeve of the old paper roll. Remove dust and paper residue from the roll compartment.
Insert the new thermal paper roll as shown in the illustration. The end of the paper should be approx. 5 cm behind the rubber roller.
Close the paper compartment again. The lock must engage audibly.
Please note:Use paper rolls with a maximum diameter of 37 mm and a maximum width of 57 mm. Available in our Accessories shop.
4. Terminal on/off
The terminal starts directly after the green button is held down for a few seconds.
The terminal is switched off using the up arrow on the touchscreen. Then press the red power button and press the yellow power button again. Then confirm "Really switch off?" with the confirmation button [O] to confirm.
Only a power supply unit approved by CCV for this type of terminal (with CE mark) may be used.The power supply unit supplies the terminal with the appropriate power. Please ensure that no additional devices are connected to the main device or the power supply unit.Damaged components of the power supply (cables, plugs, etc.) cannot be replaced by the user. In this case, the components must be taken to our maintenance service to carry out the appropriate repairs and/or reinstallation.5. Establishing an Internet connection
Please note:Routers are always supplied with DHCP active in the standard configuration.
DHCP must be active on the router. If this is not the case and the settings of your own router are known, follow the instructions on the next page.
5.1 WLAN
If mobile radio and WLAN are active at the same time, the terminal primarily uses the WLAN connection and mobile radio as a backup. Switching between mobile radio and WLAN takes place automatically.* Preset password
00 00 00
Please change the PIN after initial registration.
5.2 Connect network/DSL via manual entry (without DHCP)
If mobile radio and WLAN are active at the same time, the terminal primarily uses the WLAN connection and mobile radio as a backup. Switching between mobile radio and WLAN takes place automatically.Please note:The spelling of the IP address on the terminal must be correct.
Example:
Spelling of IP on the router: 192.168.2.1
Spelling of IP on the terminal: 192.168.002.001Please note:The terminal is delivered ready for operation. If this is not the case after checking the DHCP, network/DSL and power connection, please contact our Customer service.
V 400 m V-400m V400m V400-m V/400m